Fittings

What are strut fittings?

Fittings are the next essential part of the strut system. They provide the necessary connections to build racking, pipe supports, electrical grids and many other support applications. The majority of strut fittings are punched with a 9/16” hole to accommodate ½” threaded hardware.

**Three Hole Splice Flat Plate Fitting**

**Three Hole Swivel Flat Plate Fitting**

**Two Hole Parallel Splice Flat Plate Fitting**

**Extended Flat Angle Flat Plate Fitting**

**Two-Hole Rack 90 Degree Angle Fitting**

**Two-Hole End 90 Degree Angle Fitting**

**Two-Hole 90 Degree Angle Fitting (Indented)**

**Three-Hole Rack 90 Degree Angle Fitting**

**Three Hole End 90 Degree Angle Fitting**

**Three Hole Rack Corner 90 Degree Angle Fitting**

**Five-Hole Corner Splice 90 Degree Angle Fitting**

**Gusset Corner 90 Degree Angle Fitting**

**Four-Hole Rack Corner 90 Degree Angle Fitting**

**Universal Corner 90 Degree Angle Fitting**

**Four-Hole Corner 90 Degree Angle Fitting**

**Left or Right Hand 90 Degree Angle Fitting**

**Slotted U-Supports for 1-5/8" x 1-5/8" Strut Channel**

**Slotted "U" Supports for 1-5/8" Strut Channel**

**"U" Supports for 1-5/8" x 2-1/16" Strut Channel**

**"U" Supports for 1-5/8" x 1-5/8" Strut Channel**

**"U" Supports for 1-5/8" x 13/16" Strut Channel**

**"U" Supports for 1-5/8" x 3-1/4" Strut Channel**

**"U" Supports for 1-5/8" x 1-5/8" Double Strut Channel**

**"U" Supports for 1-5/8" x 1" Strut Channel**

**2-Hole Splice for 13/16" Strut Channel**

**3-Hole Splice for 13/16" Strut Channel**

**4-Hole Splice for 1-5/8" Strut Channel**

**Single Adjustable Angle Brace Fitting**

**Double Adjustable Angle Brace Fitting**

**Six-Hole Three Side Corner Angle Connector**

**Eight-Hole 90 Degree Corner Angle Connector**

**Eight-Hole Gusseted Corner Angle Connector**

**Nine-Hole Three Side Angle Connector**

**Six-Hole 90 Degree Corner Angle Connector**

**Eight-Hole Opposing Side Angle Connector**

Types of strut fittings include:
• Square washers
• Flat plate fittings
• Swivel plate fittings
• Angle plates
• T-shaped plates
• Cross plates
• Corner plates
• Gusset flat plates
• 90-degree angle fittings
• Z-shaped fittings
• U-shaped fittings
• Splice fittings
• Open angles
• Closed angles
• 2-Side angles
• 3-Side angles
• Corner angles

Fittings Specifications
Material	ASTM	ASTM Description
Hot Rolled Plate	A 575	Steel, sheet and strip, carbon drawing quality, special killed, hot rolled.
Fitting (Steel)	A 366	Steel carbon, cold rolled sheet, commercial quality structural steel
	A 366
	A 36
Strip Steel: Pipe Clamps	A 569	Steel, sheet and strip, carbon drawing quality special killed, hot rolled.
Stainless Steel: (ST304 or ST316)	A240 TYPE 304	Heat resisting chromium and chromium -nickel stainless steel plate, sheet, strip for pressure vessel.
Stainless Steel: (ST304 or ST316)	A 240 TYPE 316
Aluminum: (AL)	B 221	Aluminum alloy extruder bar, rod, wire, shape and tube.

Fitting Finish Specifications
Finish	Finish Code	Description
Paint-Green Coating	GR	A dark green low gloss coating is applied and thoroughly baked after steel has been cleaned and phosphatized.
Electroplated	EG	Wesanco fittings and hardware supplied as “Electro-Galvanized” in accordance with ASTM B 633.
Mill-Galvanized (Pre-Galvanzied)	PG	Galvanized steel used in the manufacture of Wesanco channel sections conforms to ASTM A 653 GR33 G90. Uncoated edges resulted from slitting, punching and channel are present.
Hot Dip Galvanized After Fabrication (HDGAF)	HG	Wesanco channel and fittings which are hot dip galvanized after fabrication conform to one to the following specifications. ASTM A 123, ASTM A153 or ASTM A 386
Special Coatings	PL, GOLD	Other commercially available finished can be supplied per specification when required to protect applications.